Parquet installation – instructions and tips from professionals

Parquet installation – instructions and tips from professionals

In the beginning, the advice of the professionals is that before setting the parquet floor it needs to be unpacked for at least 24 hours in the place where it will be placed. Avoid keeping the parquet directly in the sun or directly on the concrete surface. The wood needs to “breathe,” and you need to be careful not to dry it out or change its color on the sun.

Before starting the parquet setting, you need to check the base. It must be straight and dry. The permissible humidity of the substrate is 2 percent, and if the substrate is not flat, you need to level it. If it is necessary, under the parquet floor, you can install insulation for sound absorption as well as a foil as a steam boiler in the rooms underneath where the uncured spaces (basement, stairs, etc.) are located. These insulations are purchased in rolls and are easily placed on the substrate.

How the parquet is installed

floor1. On a flat and dry surface, pull out the direction of the first-row installation. Slacken the adhesive on the surface and start setting the parquet. Make sure the parquet is about 1 cm (0.39 inch) away from the wall and secure it with pegs. Free space to the wall will allow the parquet to move due to swelling or shrinkage with the change of humidity in the room. You need to check the direction of the first row of parquet with the help of the canopies. Set the fixing bolts at 1 cm (0-39 inch) from the wall

2. To fit the last piece of parquet properly in a row, use a steel pile profile.

3. Start the second row with the rest of the previous one.

4. Drill holes for radiators. Cut the last part and seal it in place with glue.

5. Place the parquet at the ends of the room with the help of a steel pile profile.

6. The remains of the glue remove from the parquet with a slight spatter or wet cloth.

7. In the end, tape or screw the corner battens. Slide or screw the moldings on the wall and not on the parquet floor to allow the “work” of the parquet itself. The average height of the slats is about 3.5 cm (1.3 inches), but for aesthetic purposes, we recommend those higher heights.

Make sure that the adhesive is not applied to the entire surface at one time but gradually to smaller surfaces. Professionals advise you to use high-quality adhesives because, in addition to good adhesion, they are odorless, so you do not wait for days for unpleasant smells from the apartment to disappear.

Tips for renovating the kitchen – Part 2

Tips for renovating the kitchen – Part 2

You decided to restore your kitchen, but do not know where to start? Here are some tips to help you refurbish your kitchen, create a better, more functional and modern space, all in our “Part 2“ that will help you with this quest.

Buy new items for a more modern kitchen.

When renovating your kitchen, you will surely spend the most money on kitchen items. You can avoid costs by refurbishing the existing elements. If the layout of your items is the same as before, you can save and replace only the fronts. If you have decided on new items, try to find a professional who will make you a custom kitchen.

Kitchen appliances are indispensable.

The indispensable devices in each kitchen are a fridge, a dishwasher, a stove, and sinks. If you think that the existing elements are still functional and can serve you further, there is no need to buy new ones. Enjoy your kitchen by buying a new dishwasher, and you have a lot more free time.

Work surface

Of whatever material, the worktop is a very important element of your kitchen. For the material of the worktops, the most commonly used is granite in different colors. You can even take wooden surfaces that are very commonly used lately. When selecting the worktop, choose colorful materials. White and black are quite ungrateful because every trace is visible on them.

Sink and faucet

sink2Without a sink and kitchen taps, the kitchen is inconceivable. Do not save on sinks and faucets. There is a wide range of products available at your disposal. Sinks made of stainless steel are the easiest to maintain because of their smooth surfaces. By choosing a two-hole sink, you will not make a mistake. We recommend a single-handle bowl and a built-in shower for easier washing of the sink after use. Brass taps are not a good choice, pick those of brushed or polished nickel.

Lighting

Keep in mind how you can not illuminate the kitchen area with a single light body. Especially if it is on the ceiling. We recommend the installation of LED lights above the work surface, or below the elements, which will make it easier for you to work in the kitchen. Install lighting in kitchen elements to achieve a better ambiance that will bring warmth to the room, reduce shadows and welcome every visitor to your kitchen.

How to put wallpapers

How to put wallpapers

Choosing a wallpaper is a matter of taste. Since the walls under the covers are very dominant in space, it is best to consult with the interior designer. Please note that children’s wallpaper is mostly made of paper. Since the paper wallpaper spreads in contact with moisture, the adhesive must be applied on the wallpaper and on the wall itself. For other wallpaper materials, this rule does not apply; the adhesive is applied only to the wall.

Pay attention to how to fit the patterns to make the wallpaper look uniform. Be careful on how the adhesive is applied to the walls and when the brush is used and when the roller is used. Always extract excess air between the wallpaper and the wall.

Procedure for gluing wallpaper

To begin, cut the wallpaper to the height of the room. Take care to fit the patterns. Place the wallpaper one next to the other to measure the size of the fit, mark the surplus and cut it with a scalpel. Refill the adhesive according to the manufacturer’s instructions. Apply it on the wall with a brush around the switch and in the corners, then apply it to the larger surfaces with the roller. Mark the vertical gauge of the first wallpaper with a laser meter. The wallpaper is glued to the wall from top to bottom.

Slip the air out of the rubber roller, and then scalpel cut the wallpaper around the sockets and the switch. Apply the adhesive again and place the next strip of the wallpaper taking care of fitting the pattern. The edges of the two strips must be ideally attached to each other. If they are folded or if space is left between them, the wall will look untidy.

Rub the rubber roller back on the wallpaper, and if there is a surplus of adhesive on the joints, wipe it with a clean cloth. Cut the surplus wallpaper at the ceiling and side walls with a sharp scalpel and use a lantern for leveling. Replace the sockets and switches, and the gluing is complete.

How to seal photo prints on a wall

How to seal photo prints on a wall

Each wallpaper has labels that must be followed. They define the type of adhesive and the way it is applied. The wall on which the wallpaper should be attached should be dry, clean, and smooth. It is advised that the substrate is painted in a white or neutral color so as not to break the previous color through the wallpaper.

Basic steps:

1. Unwrap the roll and cut off with the scissors in the marked places.

2. Each cut part of the wallpaper has a mark on the top. It contains product information as well as a number indicating the sequence of gluing. Cut out the tags after you paste the wallpaper onto the wall.

3. Measure the width of the roll and transfer the value to the wall. Photocopies are set clockwise, which means you need to stick from left to right of the room.

4. At the previously marked edge of the first length of the wallpaper, pull the vertical line that will serve as the direction of the wallpaper. It is very important that the first lane of the wallpaper be set at right angles because everything follows the next one. Apply adhesive to the wall in thin layers using a roller and brush.

5. Tap the wallpaper in place using a soft, clean cloth. Align the wallpaper with a rubber roller and avoid excess air behind the wallpaper. Place the second width of the wallpaper at the edge of the first roll and repeat the procedure carefully by matching the pattern. Remove excess glue using a soft cloth or sponge but do not rub.

6. Cut the ends of the wallpaper with a scalpel that you laid on a long flat lath or a lanyard. When cutting, place the scalpel at a lower angle so as not to split the wallpaper.

7. Align the wallpaper using a rubber sponge or damp cloth. It’s important to push out all the air that may have stayed behind the wallpaper. High heat or low air quality can cause the opening of the joints.

Roof Maintenance and Improvement

Roof Maintenance and Improvement

When you think of your home, what is the first thing that comes to your mind?
Do you ever think that it need’s to be a roof? And here’s why…

Your roof protects you from all kinds of bugs, animals, weather and falling debris. But, even so, we only think about the roof until it’s too late. After that, installation of new one can be a big investment. A roof can last up to 25 years depending on materials that are made of and maintenance that you do or do not. It may need replacement much sooner for reasons like low-quality materials or poor roof installation, damage made by a storm or snow and ice.

For your home, quality roofing material is a must. Second, you need an expert for installation if you want a long-lasting roof. When the roof is out of order, the whole house can easily go “out of order,” and that’s where the problems start.

There are few things that you can do to extend the life of your roof.

repair roofTwice a year you need to check the condition of your roof, walk around and try to see if there are any loose or missing flashing, sagging or broken gutters, piles of leaves in gutters, if you can clean the gutters, look around for any trees that are too big or too close to your home, one big storm can make damage to your roof. Check the insulation and try to keep your attic well ventilated, that can help you in winter when snow and ice are there.
If your roof is not green but becomes green, it can easily be that it is moss. And you don’t want moss on your roof. This buildup of algae can and will promote premature failure and deck rot; if you don’t deal with it in time, it may cost you a lot after it. You can take a broom and try to sweep it away. If you can’t to do it by your self, call us, and we will do it for you.
Slate tile, metal or asphalt shingles, you’re always looking for similar issues. Don’t ignore your roof; you may only need a portion of the roof to repair and not the whole roof.

If you wait for maintenance up to a moment when there is water dripping in your living room than you can be sure that you need a new roof. Don’t wait that long.
Your roof is more than just a shingles; it is your shield in day and night.

Nowadays, many different materials are used for making roofs. You can choose between wood shingles, slate, metal roof, asphalt shingles and many more.

We can offer you roofing products that will provide lasting durability and also the improved look of your home. Our roofing experts are here with one goal, and that is that installation of your floor need to be done properly, efficiently and first of all, safely.

7 required steps to replace the roof windows

7 required steps to replace the roof windows

Do you have old and worn-out roof windows? Are you finally thinking of a replacement? These are the steps you must keep in mind if you want security, comfort and a pleasant ambiance under your roof. It is all you need to know to do it yourself.

  1. Removing the old window

The first step is certainly dismantling the old window, and before disassembly begins, it is necessary to take safety measures and prevent unwanted consequences. It is because the window you are replacing is often in a very bad condition and there is a possibility that it breaks in its parts (glass, locks). That is why you always need to be careful.

  1. Preparation of the opening in the roof construction for the new window

The most common reason for replacing windows is the breakthrough of water on the window itself, and part of that water is always somewhere in the roof construction. Therefore, when dismantling the old window, always check the condition of the roof structure at the place where the window was, and, if necessary, replace the rotting parts of the wooden roof structure.

  1. Installation of the roof window

roof windowThe installation of the roof window is done exclusively by the installation instructions and by the manufacturer’s specification. Therefore, no matter how convinced you are in your skills and knowledge, do not install windows at your discretion, but according to the precise instructions that very serious manufacturer instruction book that comes alongside their windows. If you make any damages to the purchased window, the company who sold it to you will surely not help you if you went off the instructions.

  1. Removing the roof

An important role in the installation of the roof window is the proper removal and the installation of the roof cover around it. Only the properly installed roof cover around the window provides waterproofness between the windows and the roof cover.

  1. Making the inner lining around the roof window

The basic rule is that the top surface of the lining is horizontal and the lower surface of the lining is vertical. When replacing the roof window, be sure to follow this exactly.

  1. Installation of blinds

The last action when installing a window is the installation of blinds that will regulate the amount of light. Shutters are installed after the completion of all works so you will not damage them or install them improperly

  1. Regular window service

An extremely important thing for the window’s longevity is their maintenance and regular servicing. Unfortunately, in practice, this paragraph is often neglected in the long run, and that can create much greater losses.